Explore Military Aircraft Flight

Hi! I’m from the window-valance-patterns.com and if you sawing swag curtains and jabots I’m going to show you the absolute easiest way for you to install that layer window treatment onto the drapery rug it’s called swag/jabot mounting tape and it is the newest tool to use and this stuffs will going to make your installation job really easy. Your swag curtain should look something like this now, your fabric is pleated and you have a long strip stitch about one inch from the top raw edge here the whole those pleats in place. Next you are going to take swag jabot mounting tape that essentially is a built craw tape both hook and loop at the same time. One side has the hook and the other side has the loop tape, the loop size is soft and fuzzy and the hook is kind a rough. You are going to lie this so that the rough edge of your pleated swag here is going to align along this middle edge here okay. The hook side is going to go to the lying side of your swag and the soft classy side the loop side is going to go on top of your swag like this. So it’s going to essentially fold over that raw edge. Now the strip of your jabot swag mounting tape should be about an inch longer than you need to cover that raw edge, it doesn’t have to be perfect we just want some extra to hang off on each side and once you’ve have this folded neatly over about raw edge of your pleats you are going to secure this by to seal along the edge here to hold everything down. Okay so now I’ve stitch along this edge here to secure the jabot swag mountain tape to my pleated edge may point toward you a little bit so could see that and you could see I have a few bubbles here but it doesn’t have to be perfect and you never go to see this one its installed and the whole purpose that your going to have a layer of the loop side and then the hook side on the back. This is going to be very, very handy especially if you are using multiple layers of swags, many times you’ve got them easily connecting one after the other after the other and now if each one has a hook on the back and a loop on the top the hook will stick to the loop and you can easily have a jabot under this and look the same tag of edge and you can remove and attach as need to adjust okay. Now you still have your sloppy ends here and know it really easy to meeting up, if it’s too long on the edge here just put it down a little bit about one inch from the swag and you are going to cut out the hook back of this to hit this part of the front here. So you just cut along the top folded edge there and cut off that piece so you just have the soft piece in the front and flip it over and you are just going to fold this into a little triangle here and then over to the hook side just to attached so it just nice and neat and you do that at other side as well. And cut out this little thread you see here. Okay and that’s it, now how to install it is actually even easier take some one inch pressure sensitive bilker tape and as you can see we have a pair of plastic piece you can just pull off so the pressure sensitive means you’ve got a real sticky back here real strong sticky back. So this is what’s going to stick to your drapery, your drapery pull or even to your desk board if you are going too mounted to a board. And you cut a strip the same length as the mounting tape that you sawn to your pleated edge and back up a little bit so you can see. Now this is loop tape and since you’ve sawn this mounting tape to the top edge the back edge is hook tape so this is easily just stick straight to the bilker tape. Now that is stop here and you could easily now remove it and readjust as needed when you take it to your drapery you are going to pull off the sticky bat here and sticky tray you want onto your drapery pull. Now ideally you want this to appear as the swag drape over your pull so you’ve want to stock to the back part of your pull so you don’t see any of this on top of your pull. You don’t want to the frame of your pull you really don’t want on the top of the pull you kind a want forwards the back of the pulls everything kinds to the drapes over. If you are going to this with thus for you simply stick it to the top of your desk board everything will drape down and you’re not going to see this up to the top okay. So I’m going to do this same thing else to the other side of mind at my swag curtain here I haven’t done this side yet and when I’m done I’m going to install onto the poll and I will show how that all that looks. You can get your swag jabot mounting tape and your one inch pressure sensitive loop tape at draperysawingsupplies.com to instantly download of the eBook for sawing swag curtains and jabots click on the 15% coupon below to receive at this count on your next purchase at window-valance-patterns.com.